Significantly reduce evaporation and contamination by using a Thermo Scientific™ Nalgene™ Rectangular Polypropylene Tank with Cover, offered in sizes ranging from 8 to 114L. Tanks can be modified with a factory-installed spigot. Features: Suitable for use with many…

Heavy duty, molded TLC developing tank for use with plates up to 20 x 20 cm (8in x 8in). The weight of the tank is approximately 15 pounds and the bottom is ground to insure stability. The unique latching system holds the matching ground surfaces of the lid and tank firmly in place, enhancing the…

Resist stress cracking and increase tolerance to many organic chemicals with the Thermo Scientific™ Nalgene™ Cylindrical Polypropylene Tank with Cover, an economic alternative to stainless-steel tanks. Autoclavable cylindrical tanks are available in sizes ranging from 19L to 378L…

The Advanced Projection Ripple Tank is a comprehensive system for demonstrating basic wave phenomena using water waves. A horizontal glass plate is mounted in a watertight frame with foam beaches around the perimeter to suppress unwanted wave reflections. This tank is mounted on three tall legs…

Stainless steel Strong spring-loaded autoclavable clamps assure tight, leakproof fluid connections. Recommended for use with 2261 series carboy.

Cylindrical glass chamber for development of TLC plates from 25 x 75mm to 50 x 200mm. Chamber has a short length standard taper outer joint. Stopper is a short length inner with a tool ball style handle. The CG-1181-01 and -02 chambers have a hex base for added stability. Complete chamber is…

Polyvinylidene fluoride All plastic autoclavable threaded clamp system Recommended for use with 2630 and 2640 series carboys, 2688 and 2689 series end caps

Can be stacked to minimize storage space. High chemical resistance to organic and inorganic acids. Robust with lifting lugs and strengthening ribs to ensure long life.

Rectangular, Linear low-density polyethylene (LLDPE) with cover Similar to 9075D10 series, but rectangular With friction-fit covers Resin complies with FDA Regulation 177.1520 for food use Nalge recommends using FRP casing or exterior support with all rectangular tanks used…

1 1/8” Needle Spigot for Biotech Closed Dome Tank Polypropylene

Replacement Lid only.

Transparent polycarbonate reservoir lets you keep samples in clear view Elevated tank bottom provides secure hand holds when lifting or relocating bath, remains stable on uneven surfaces Drain ports on 17, 23, and 28L models Use with Thomas® MX Immersion Circulator to create an open bath

Corning’s portfolio of irradiated tank liners are designed to fit cylindrical tanks. Tank liners are manufactured with low-density polyethylene (LDPE) and are available in a range of sizes. Features and Benefits Gamma irradiated, individually packaged Free of animal-derived…

Storage Tanks Theses straight sided cylindrical tanks with cuff flange are ideal for a wide range of chemical applications. • Made of a UV stabilized LLDPE • Translucent & graduated for monitoring level of liquid • Flared top edge for extra support •…

Natural polypropylene Use end caps to securely close off 3/4" or 3" sanitary port Groove on underside of end cap accepts standard sanitary gasket Autoclavable end caps meet USP VI requirements and comply with 21CFR177.1520 for food use

Nalge 2651 Polyvinylidene fluoride For use with all sizes of closed-dome tanks (9074T30 through T70) Sanitary flange assembly permits overhead mixing in a closed system Autoclavable closure consists of 6” polypropylene screw closure with 2” sanitary ferrule welded in…

An economical alternative to stainless steel, the Thermo Scientific™ Nalgene™ Lightweight Cylindrical LLDPE Tank with Cover and Spigot offers excellent resistance to stress cracking and features a spigot installed for draw off. Ideal for less rigorous applications. Available in sizes…

PTFE coated aluminum rack to fit either CG-1183 or CG-1184 TLC developing tank. Rack will hold six 20cm x 20cm x 1/8in or twelve 20cm x 20cm x 1/16in plates.

WaterPro RO Bladder Tanks provide additional storage of reverse osmosis water produced by the WaterPro RO Station. The pressurized water can be distributed to a polishing station (such as the WaterPro® PS) or to a glassware washer (such as the FlaskScrubber® or SteamScrubber®) through…

Enhance mixing capabilities with open-bag, flat-bottom liners. Thermo Scientific™ Nalgene™ Coex Polyethylene Film Tank Liners offer cost-effective, single-use biopharmaceutical and diagnostic reagent fluid processing with rigid Nalgene cylindrical plastic tanks. Coex Polyethylene film…

Latch lids are designed to hold the lid firmly to the developing tank, greatly improving the stability of the saturated environment for developing TLC plates. Knob for easy lifting PTFE retainers inside prevent the lid from accidentally sliding off the tank Manufactured from sturdy…

For an economical alternative to stainless steel, choose the Thermo Scientific™ Nalgene™ Lightweight Graduated Cylindrical LLDPE Tank with Cover. Ideal for less rigorous applications, these linear, low-density polyethylene tanks offer excellent resistance to stress cracking. The cover…

Corning’s portfolio of irradiated tank liners are designed to fit cylindrical tanks. Tank liners are manufactured with low-density polyethylene (LDPE) and are available in a range of sizes. Features and Benefits Gamma irradiated, individually packaged Free of animal-derived…

Heavy duty, molded TLC developing tank for use with plates up to 20 x 20 cm ( 8in x 8in). The weight of the tank is approximately 15 pounds, and the bottom is ground to insure stability. Inside dimensions of the tank are 27cm wide x 7cm deep x 26 cm high (10 5/8in x 2 7/8in x 10in). Tank is…

Linear low-density polyethylene (LLDPE) (9075D10 - D60) Not autoclavable Rigid, seamless Flanged rim has upturned edge. Tank includes friction-fit cover. It is resistant to most acids, alcohols, aldehydes, bases, esters, ketones and aliphatic and aromatic hydrocarbons; not…

Store, mix and dispense reagents in Thermo Scientific™ Nalgene™ Closed-Dome Polypropylene Tanks, designed for use as closed containment systems. Offered in sizes ranging from 75 to 380L , tanks featurea a 150mm neck opening fitted with a gasketed closure for secure sealing. …

Platinum cured silicone Recommended for use with 2261, 2630 and 2640 series carboys and 2688 and 2689 series end caps. Autoclavable Meets USP Class VI requirements.

Compact size offers good plate visibility and minimal solvent use. Can be used as a staining chamber Made of glass with lid