Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Low bleed, longer life alternative to standard septa for split/splitless injection Has a lifetime of more than 2000 injections, depending on samples and operating conditions Reduced instrument downtime for septa changes and injection port liner changes due to septa particulates Two…

MicroLiter septa for 9mm Screwthread Autosampler Vials are constructed with a wide array of chemical compatibilities to suit a variety of chromatography applications.

Specially engineered to fit standard taper joints and tubes. Manufactured under white room conditions for extreme cleanliness. Made of a more dense rubber, low extractables and a better fit (50% to 80% on joints) these septa are much less likely to fail in the presence of solvents.

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

MicroLiter septa for 16mm Screwthread Headspace Vials are constructed of PTFE, PTFE/butyl, or PTFE/silicone to suit a variety of chromatography applications.

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Replacement septa for 8-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

Long injection life, pre-pierced for minimal coring. Maximum temperature 400°C. Long injection life septum typically achieves 400 injections without failure, when used with a rounded-tip (Agilent-style) needle and autosampler or needle guide. Ideal for standard manual-injection GC and GC/MS. 3 mm…

Single septa for all 20 mm crimp caps from MACHEREY-NAGEL Butyl / PTFE: temperature resistant: –40 °C / +120 °C, medium analytical purity, medium coring, medium hard to penetrate, resealability medium Silicone / PTFE: temperature resistant: –60 °C / +200 °C high…

Butyl stoppers can be used when PTFE is not required. Butyl/PTFE septa are an economical choice with low background peaks. Molded PTFE/butyl septa offer the tightest seal of all PTFE items, as well as low background peaks. PTFE/silicone septa are excel

The Agilent Technologies inlet septa is made from strong silicone material and works well even at 35 degree C temperatures. This septa is compatible to use with 5880, 5890, 4890, 6850, 6890, 7890 GC columns. Application: For 5880, 5890, 4890, 6850, 6890, 7890 GCs This product is only available…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Material: Red Silicone Septa L x O.D.: 0.308 in. x 0.125 in. Legal Information Mininert is a registered trademark of Valco Instruments Co. Inc.

GC injection port septa Standard quality Septum grade: Standard septa (ST) Material: beige silicone Thickness: 4 mm Hardness: 60° shore A Septum grade: High temperature septa (HT) Material: red non-bleeding silicone Thickness: 3 mm Hardness: 60° shore A …

Maximum setpoint: 400°C Low bleed Long injection life 3 mm thick CenterGuide™ chamber in one face guide the needle with each injection.

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage. 73818A-24 ( 1213T38) is white PTFE/Tan Silicone and is recommended for use with the 40 mL EPA vial.

Feature: temp. limit 250°C

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…