An improved version over the original Thermogreen LB-1 septa. Extremely low bleed over a wide range of inlet temperatures (100 °C to 350 °C) Already conditioned, ready to use Easier needle penetration and high puncture tolerance (ideal for autosamplers) Rubber formulation…

Maximum setpoint: 400°C Low bleed Long injection life 3 mm thick CenterGuide™ chamber in one face guide the needle with each injection.

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Aluminum seals with pre-inserted septa are compatible with standard opening crimp top vials, wide opening Target LOVial™ crimp top vials and Target Snap-it™ crimp/snap vials.

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

MicroLiter septa for 9mm Screwthread Autosampler Vials are constructed with a wide array of chemical compatibilities to suit a variety of chromatography applications.

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Single septa for 13-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C, medium…

Ideal for use in removing fibrin and macro particles from serum to prevent line clogging. Users insert the 16 mm flange into the evacuated blood tube and push downward. The graduated barrel tells exactly how much liquid has been filtered and the wide-body style prevents sample probes from…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Long injection life, pre-pierced for minimal coring. Maximum temperature 400°C. Long injection life septum typically achieves 400 injections without failure, when used with a rounded-tip (Agilent-style) needle and autosampler or needle guide. Ideal for standard manual-injection GC and GC/MS. 3 mm…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage.

Material: Red Silicone Septa L x O.D.: 0.308 in. x 0.125 in. Legal Information Mininert is a registered trademark of Valco Instruments Co. Inc.

GC injection port septa High quality CenterGuide™ for centered needle guidance for a perfect fit Highest septum quality for minimal bleeding, even at high temperatures up to 400 °C (Shimadzu plug septa up to 300 °C) Precision trough for a perfect fit Special coating…

Butyl stoppers can be used when PTFE is not required. Butyl/PTFE septa are an economical choice with low background peaks. Molded PTFE/butyl septa offer the tightest seal of all PTFE items, as well as low background peaks. PTFE/silicone septa are excel

For use with 12 x 32 mm crimp top vials Large target diameter Available in 4 colors Choice of liner

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Specially engineered to fit standard taper joints and tubes. Manufactured under white room conditions for extreme cleanliness. Made of a more dense rubber, low extractables and a better fit (50% to 80% on joints) these septa are much less likely to fail in the presence of solvents.

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…