Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Low cost, good resealability Polytetrafluoroethylene provides barrier for product contact Red rubber

Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

22 mm Septa for VOA Vials PTFE/Silicone Liner

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

The Agilent Technologies inlet septa is made from strong silicone material and works well even at 35 degree C temperatures. This septa is compatible to use with 5880, 5890, 4890, 6850, 6890, 7890 GC columns. Application: For 5880, 5890, 4890, 6850, 6890, 7890 GCs This product is only available…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Synonym: rubber caps, rubber stopper, rubber stoppers Usage: for 5-6 mm O.D. tubes and ampules Color:   white General description Engineered for a "push on" fit in NMR tubes and ampules. The unique design provides a penetration point for cannulation and a dual…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

GC injection port septa High quality CenterGuide™ for centered needle guidance for a perfect fit Highest septum quality for minimal bleeding, even at high temperatures up to 400 °C (Shimadzu plug septa up to 300 °C) Precision trough for a perfect fit Special coating…

Single septa for all 20 mm crimp caps from MACHEREY-NAGEL Butyl / PTFE: temperature resistant: –40 °C / +120 °C, medium analytical purity, medium coring, medium hard to penetrate, resealability medium Silicone / PTFE: temperature resistant: –60 °C / +200 °C high…

Replacement septa for 9 mm screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

Septa closure with locking flange for open-top caps. Flat stopper; thin flange Cap size: 33 mm Gray Chlorobutyl/50 septa

For 20 mm vials Temperature range: 40° to 120°C Does not provide PTFE barrier Not suitable for alkalines, benezene, chlorinated solvents or cyclohexane

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Three Layer Septa is made of preconditioned silicone rubber and is 3.81 mm (0.150 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 200° C. Preconditioned silicone rubber septa, 3.81 mm (0.15“) thick …

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent now treats each premium 11 mm inlet septa to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Agilent's premium septa also have a recess on the injection side, to guide the syringe needle to the same point…

Agilent now coats each premium 11-mm inlet septa with plasma to eliminate sticking in the GC inlet. With our premium non-stick septa, you'll never have to scrape bits of septum out of your inlet. Our premium septa also have a recess on the injection side that guides the syringe needle to the same…

Agilent's general-purpose septa are made from an enhanced injection-molded silicone rubber material. The septa material, dark red or gray in color, is specified to withstand over 200 automatic injections at an injection port temperature of 350 °C. You can have confidence in your chromatographic…

Inlet septa are used to maintain a leak-free seal under the septum nut in the GC inlet, even after many repeated injections. The dimple in the middle of the septum guides the syringe needle through the inlet into the inlet liner to minimize damage to the needle and to ensure injection consistency.…