Heavy duty, 28mm O.D. glass stirring shaft for use with ACE 12845 reactors. Shafts are pre-drilled to accommodate 8091,8093 & 8101 agitators for 28mm od shafts. Recommended for use with either our 8067 Trubore™ bearing with debris trap or our 8050 non-shedding bearing. For motor connection,…

Precision ground glass stirring shafts, 19mm OD, hollow. Button type shafts accept 8085 blades and can be used in all 19mm ID Trubore 8059, 8060, 8061 and 8065 bearings. Compatible with our 8050 mechanical seal and 13445 PTFE Debris-free bearings. Join to stirrer motor using 8124 series chucks.

The AREX 5 is a robust and versatile hotplate stirrer suitable for applications ranging from basic to temperature-sensitive where precise sample thermoregulation is required. The AREX 5 can work stand-alone or be upgraded to digital by connecting the VTF digital temperature controller. …

Features: Adjustable safety temperature cut-out: safety cut-out within the 100-580 oC temperature range is adjustable Accurate temperature and speed control: the microprocessor control technology effectively monitors the temperature and speed precision Features of digital models: Heat…

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment.  Bell-ennium stirrers offer the researcher a wide range of capabilities and the latest innovations in stirring…

Model 8583J10: Produces propeller speeds from approximately 200 to 10,000 rpm Compact and quiet; operates on compressed air at pressures from 30 to 100 psi (210 to 690 kPa) Sturdy, smooth-running motor develops 1/6 hp (120 W) at 80 psi (550 kPa) input Speed is variable by adjustment…

Impellers made of stainless steel (8592H39 through H48) or glass-filled propylene (8592H36) Autoclavable 8592H36 Lower Assembly/Shaft and Impeller; shaft length x diameter: 13-1/2" x 3/8"; impeller diameter: 4". 8592H39 Lower Assembly is for use with the Nalgene 30-gallon,…

OHAUS Achiever 5000 Overhead Stirrers are designed for powerful, precise stirring, safety and simplicity in all applications. The sealed design has an IP54 rating and ensures safe mixing performance even in the most demanding applications. The keyless chuck and software-controlled speed ramping…

Grease-Free PTFE stirrer bearing for use under moderate vacuum. The bearing consists of a PTFE standard taper body, Nylon compression cap, PTFE Insert/bushing and a Nylon loosening nut. The PTFE insert/bushing provides only glass and PTFE contact with the reaction. Loosening nut above the standard…

This bearing is the standard liquid seal type except that the use of Trubore tubing enables this unit to perform very satisfactorily under high vacuum conditions. Use our precision ground stirring shafts (8068,8070,8071,8073,9532,9533).

Powerful Magnetic Stirrers available in either four or nine position capacities provide precise speed control that deliver repeatable performance. Offered in both digital and non-digital models. Digital models have touchpad controls for input of speed & time. Non-digital models have an…

Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…

Support Stand Steel base; legs have rubber pads to cut vibration Support rod is made of stainless steel. Height is 29”; available in two models. Jacob's Chuck, Adjustable Fits 3/8 ” (10 mm) diameter motor shafts Keyless Chuck, Nylon-bodied …

Manufactured from 316l stainless steel for standard bioreactor vessels. Use with over head drive motors.

PTFE covered stainless steel stirring shafts, 10mm OD, drilled type. If used unlubricated, 500 rpm max with water cooled 8040 bearing, 100 rpm max recommended with 8036, 8038, 8039, 8043, 8047, 8051 and 8055 bearings. With condensate film as added heat transfer agent, 2000 rpm can be attained.…

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. Bell-ennium stirrers offer the laboratory researcher a wide range of capabilities and the latest innovations in stirring…

The Magnetic Induction Stirrer is motor-less, using advanced coil technology that produces the strongest magnetic coupling and has no moving parts making this unit 100% wear-free and maintenance free. The magnetic induction stirrer is ideal for use in general research, life science,…

Use Thermo Scientific™ Cimarec™ i Bath Mounts with Telesystem series stirrers. Made of transparent acrylic Capacity: 3.9 gal. (15L) Temperature Range: 0 to 60°C Dimensions: 20.4 x 12.4 x 6.3 in. (520 x 315 x 160mm)

Powerful "rare earth" magnets stay coupled even under the most demanding stirring conditions Rugged ABS/Polycarbonate housing Vortex-Genie® heavy-duty motor Three different models May be used in cold rooms and incubators

Assembly consists of a 10mm OD Chem-Stir™ stirrer shaft, a precision bore-bearing having a standard taper inner joint and a PTFE blade. The blade is sized to fit the listed flask capacities.

Unground, 9mm OD stirring shaft design for use with our 9528 vacuum and debris free stirrer assembly. 380mm straight section, 416mm overall length. Use our 9530-08 blade.

Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…

The Magnetic Induction Stirrer by Heathrow Scientific is motor-less, using advanced coil technology that produces the strongest magnetic coupling and has no moving parts making this unit 100% wear-free and maintenance free. Motor-less Magnetic Stirrer: The magnetic coil technology works on…

The IKA Plate (RCT digital) has a round top made of aluminum alloy. It stirs volumes of up to 20l (H2o) and runs at speeds ranging from 50-1500rpm. Strongly standing by its product and technology, IKA is offering a lifetime warranty on the magnetic stirrer – unparalleled in the industry;…

Stirrer blade made of 1/8" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 10mm OD.

Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated…

The Hot Plate or Heating Mantle with Magnetic Stirrer is ideal for simultaneous stirring and heating of liquids. The hot plate includes an integrated magnetic stirrer. Two dials allow you to control the speed and the temperature. The support arm holds a thermometer or probe. The speed range is…

These heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.

Blades Stainless steel with 400 mm shafts

Precision ground and polished stirrer shaft for use with Chemglass process reactors. Designed to utilize CG-2095 and CG-2096 PTFE agitators. Lower portion of stirrer shaft is sandblasted and has a 3/8” wide flat.  Please Note: CG-2097-75 and CG-2097-100 are made from heavy wall tubing…

RT Touch Series Magnetic Stirrers Stay in control with our low profile digital display stirrer, ideal for routine stirring applications where visible stir speed is required. FEATURES Digital control Gradual start-up stirring to prevent splashing Designed for stir rod…

High-performance multi-position magnetic stirrer with 10 stirring position, optimum use of laboratory space The stainless steel surface covers the unit allowing easy cleaning and providing protection against the penetration of liquids Simultaneously operating stirrers, absolute consistency…