PTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.

Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.

Uniquely designed and lubricant free, these precision stirrer/stirring bearings are self-aligning. The saddle O-ring provides constant force and a positive seal on the stirring rod that allows vacuum operation to as low as 1mm. Ground finish rods from other manufacturers are not recommended for use…

SIBATA 47mm Filtration Filter Holder Components are available as replacement components, or to create a customized filter holder. Available with fritted glass support base for general and biological applications, or with removable stainless steel screen support base and PTFE gasket for ultraclean…

Grease-Free PTFE stirrer bearing for use under moderate vacuum. The bearing consists of a PTFE standard taper body, Nylon compression cap, PTFE Insert/bushing and a Nylon loosening nut. The PTFE insert/bushing provides only glass and PTFE contact with the reaction. Loosening nut above the standard…

Stirrer blade made of 1/8" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 10mm OD.

Eliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…

Shafts are 316 stainless steel. All 3/8" (9.5 mm) dia shafts are machined on one end to accept a 5/16" (8 mm) bore diameter propeller.

10mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/4" diameter stainless steel…

Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…

Use these three-bladed electro-polished propellers for your general-purpose mixing. Use singly or mount several on a shaft for thorough agitation. Choose marine-style propellers for your general-purpose mixing or choose turbine style for your airless mixing in deep containers. Dispersion…

High viscosity agitator, made entirely of PTFE and glass filled PTFE, provides excellent stirring at the bottom of 2L through 20L reactors, especially when heavy slurries are being mixed. Agitator attaches to stir shaft by both a compression fitting and a glass filled PTFE safety pin. Heavy…

Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.

Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…

A 10mm precision ground and polished stirrer shaft to fit CG-2076 and CG-2077 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2075.

4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.

Features: UL 61010-1, CSA C22.2 and CE certified (available by request, additional cost) Filter reactors for single or multi-step reactions and filtrations in the same vessel, they also eliminate material transfers and reduce losses. Modular filter assembly can be easily detached for…

Precision bore bearing for use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

Unground, 9mm OD shaft for use in liquid seal bearings and our debris free 8098 and 8099 stirrer assemblies. Code -25 is a button type shaft which accepts our 8083, 8084, 8085 and 8086 blades. Shaft length accomodates flasks from 500ml to 5000ml.

Universal Stirrer Shaft Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench. …

PTFE multi-paddle agitator for 10mm OD drilled or knob type shafts. Paddles are replaceable. Fits 10mm OD drilled or knob type 8068, 8071 and 8079 shafts.

A turbine type agitator, available for 19mm and 28mm shafts. 19mm six blade agitators are open in the center to allow custom positioning on drilled type or knob type 8076, 8078 & 8079 shafts. 28mm four blade agitators are supplied with a PTFE nut & bolt set for securing to 8080 shafts. Shaft is not included.

Precision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.

Grease-Free PTFE stirrer bearing designed for use under moderate vacuum applications. The bearing consists of a threaded glass adapter having an inner joint, a set of PTFE washer style bearings, a stainless steel spring, nylon alignment ring and Celcon® compression cap. The unique design of…

Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055.…

Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…

All-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE…

316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.

Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.

Stirring shaft with steel core. Use with PTFE stirrer guides and for applications which do not require a guide. Unbreakable, scratch resistant, and usable up to 280C.

PTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.