Condensers Products (186)

Compare Tool

Select up to 3 products

  • Thumbnail Image for Vigreux Distilling Columns

    United Scientific Supplies

    A Vigreux column is a type of air condenser where the simple tube has been modified to include an abundance of downward-pointing indentations. This dramatically increases the surface area per unit length of the condenser. Includes a 24/40 connector.

  • Thumbnail Image for PYREX Graham Condensers

    Corning

    Graham Coiled condensing tube is sealed into water jacket Inlet and outlet tubes on opposite sides of jacket With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has 19/38 joints; others have Standard Taper 24/40 joints

  • Thumbnail Image for Keck Clips

    United Scientific Supplies

    Plastic conical joint clips are size 24, designed to securely hold 24/40 joint size glassware together.  Note: Clips shipped are blue

  • Thumbnail Image for Findenser - Super Air Condenser

    Heidolph

    Findenser comprises of an internal glass condenser and an external, finned aluminum jacket, between which a small amount of water is permanently sealed. The glass condenser is designed to have a greater internal surface area than traditional condensers, giving it increased heat transfer capacity....

  • Thumbnail Image for PYREX® Allihn Condensers

    Corning

    Allihn - suitable for use in vacuum distillations With condensing tube expanded by series of bulbs which increase condensing area and lengthen condensate path Inlet and outlet tubes are on opposite sides of the jacket All sizes take stopper size 3 and have Standard Taper drip tip joint at bottom and...

  • Thumbnail Image for PYREX® Friedrichs Condensers, Drip Tip, with 24/40 Standard Taper Outer and Inner Joints

    Corning

    This PYREX® Friedrichs type condenser affords very efficient operation. The helical inner tube fits closely within the jacket. The vapor tube is sealed to the jacket at an angle of 75° and has an outer 24/40 Standard Taper joint.

  • Thumbnail Image for Reflux Cold Finger Type Condenser

    Thomas®

    Of borosilicate glass All sizes have a flange on which they are suspended without use of stopper Total height of 6 3/4” Size A finger is 15 x 75 mm long; flange diameter 50 mm.

  • Placeholder Image for PYREX® Air Reflux Condenser, Standard Taper

    Corning

    This Air Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

  • Thumbnail Image for PYREX® Jacketed Reflux Condensers

    Corning

    This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

  • Placeholder Image for PYREX® Cold Finger Condensers, with 24/40 Standard Taper Inner Joints

    Corning

    This simple PYREX® cold finger condenser, of relatively low efficiency, is often used to regulate refluxing by adjusting the flow of air or water through it (dephlegmation). The tubulation O.D. is approximately 10mm. This condenser has a 24/40 inner Standard Taper joint and is a replacement part...

  • Thumbnail Image for PYREX® Liebig Condensers

    Corning

    Suitable for the use in vacuum distillations With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has Standard Taper 19/38 joints; others have 24/40 joints

  • Thumbnail Image for PYREX Liebig Condensers

    Corning

    Suitable for refluxing, extracting and distilling operations With Standard Taper 24/40 drip tip joint at bottom All sizes take stopper size 3

  • Thumbnail Image for PYREX® 250mL Chromatographic Reagent Atomizer

    Corning

    These 250mL PYREX® atomizers are used for spraying reagents onto thin layer chromatography plates. They have a full length 24/40 Standard Taper joint between the reservoir and spraying device. The PYREX® distilling condenser has 14/20 Standard Taper inner and outer joints, is simple in design and...

  • Thumbnail Image for Column 190 mm 19/22

    Corning

    The PYREX® distilling condenser has 19/22 Standard Taper inner and outer joints, is simple in design and easy to use. Side tubulations are 10mm O.D. Distilling condensers are widely used in the lab, especially for fractionation. This condenser is also a replacement for organic chemistry kit No....

  • Thumbnail Image for PYREX Liebig Condensers

    Corning

    With Standard Taper 24/40 joints Inlet and outlet tubes, 10 mm o.d. are on opposite sides, indentations at lower end of condenser tube support packing when used as fractionating column.

  • Thumbnail Image for Liebig Condensers

    DWK Life Sciences (Kimble)

    Standard Taper outer joint at the top Standard Taper inner drip joint at the bottom Hose connections accept 3/8” ID flexible tubing Ref: ASTM Method D322 Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.