Shaft Stirrers
-
Stirrer Plate Stand
ChemglassSupport Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…
-
Stirring Shaft, Unground, 9mm
Ace GlassUnground, 9mm OD stirring shaft design for use with our 9528 vacuum and debris free stirrer assembly. 380mm straight section, 416mm overall length. Use our 9530-08 blade.
-
Replacement Glass Shaft
ChemglassReplacement components for CLS-1414 and CLS-1415 Spinner Flasks.The Complete Impeller Assembly consists of top cap, silicone liner, glass rod, compression fitting magnet holder, paddle and magnetic stir bar.
-
Bearing, Trubore, Ace-Thred, 10mm
Ace GlassSelf-aligning, three-piece bearing. Complete consists of inner Trubore bearing, Nylon bushing with O-Ring, and threaded adapter. Unique design eliminates costly replacement since inner bearing will spin if shaft binds or will self-align at O-Ring seal in the event the motor is slightly cocked.…
-
Four-Blade PTFE Agitator Stirrer Blades
ChemglassAgitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated…
-
Heavy Duty PTFE 19mm Stirrer Blades
ChemglassStirrer blade made of 3/16" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 19mm OD.
-
Shaft is precision ground and polished to fit our CG-2086 19mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION. ALSO NOTE: 19MM…
-
Shaft is precision ground and polished to fit our CG-2077-H, CG-2077-G and CG-2077-U style 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR CLOCKWISE ROTATION.
-
Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
-
Chem-Stir™ 10mm Polished Stirring Shafts
ChemglassA 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir™ blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt…
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.
-
Thomas No. 1177M38 Impeller. Mixer. Blade. Crossed Blade. Radial Flow. High Speed. Low Viscosity. 316L SS. Electropolished. High Shear. High Vortexing. Thomas No. 1177M39 This radial flow impeller is effective for high speed, low viscosity mixing. The 50 mm (2”) diameter…
-
Chem-Stir™ 10mm Stirring Shafts
ChemglassEliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…
-
Button Style 10mm Stirring Shaft
ChemglassA 10mm precision ground stirrer shaft to fit CG-2070 through CG-2072 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING. FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2079.
-
A 10mm precision ground and polished stirrer shaft to fit CG-2076 and CG-2077 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2075.
-
Macro Glass Stirrer Bearings
ChemglassPrecision bore bearing for use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.
-
PTFE 10mm Stirrer Blades
ChemglassStirrer blade made of 1/8" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 10mm OD.
-
PTFE 60° Agitators
ChemglassAgitator blades are constructed of PTFE with a glass filled PTFE locking nut. This enables them to be attached to the shaft in any vertical position. Note: Designed for use with CG-2079-X, CG-2078-X or CG-2096-X PTFE Covered stainless steel type shafts
-
Beaded pipe to sanitary fitting adapter connects to the 1-1/2” beaded pipe side arm of CG-1968-GL zero dead space drain valve. Approximate overall length of adapter is 1.75”. NOTE: Requires a CG-1968 beaded pipe coupling.
-
Shaft is precision ground and polished to fit our CG-2076 and CG-2077 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The straight glass blades are spaced 90° apart and angled 15°. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION.
-
Bearing, Trubore, Gas Balancing, 10mm
Ace GlassThis bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
Chem-Stir® Macro Stirrer Assembly
ChemglassAssembly consists of a 10mm OD Chem-Stir™ stirrer shaft, a precision bore-bearing having a standard taper inner joint and a PTFE blade. The blade is sized to fit the listed flask capacities.
-
Stirring Shaft, Glass, 19mm, Polished
Ace GlassPolished glass stirring shafts, 19mm OD. Available in solid and hollow styles and in various lengths. Join 8085 blades to button type shafts, Join 8091,8092,8093 and 8100 agitators to either knob or drilled style shafts. Join all shafts to stirrer motor using 8124 series chucks. Recommended for use…
-
Anchor Style PTFE Agitator
ChemglassHeavy duty PTFE anchor made of 0.500” thick PTFE. Blade is shaped to mirror the contour of Chemglass cylindrical reactors. Designed for use with CG-2078 Chem-Stir® 10mm stirrer shaft. The blade is secured to the stirrer via a PTFE pin. PLEASE NOTE: CG-2081-A-02 IS NOT…
-
Stirrer Shaft Coupling Assembly
ChemglassThis incorporates a universal stirrer shaft coupling (CG-2046) to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Stainless steel stud and upper coupling attach directly to the motor shaft. For use with 30L…
-
Chem-Stir™ 19mm Polished Stirring Shafts
ChemglassEliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
PTFE Flake Catching Cups
ChemglassCup is designed to catch all flaking that occurs with PTFE stirrer bearings. Made entirely of PTFE, the complete item consists of a compression fitting, deep perforated PTFE cup and a 50 micron porosity PTFE filter disc.
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, standard taper joint. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts.
-
Universal Stirrer Shaft Coupling
ChemglassUniversal Stirrer Shaft Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench. …
-
Precision PTFE Stirrer Bearings
SP Wilmad-LabGlassUniquely designed and lubricant free, these precision stirrer/stirring bearings are self-aligning. The saddle O-ring provides constant force and a positive seal on the stirring rod that allows vacuum operation to as low as 1mm. Ground finish rods from other manufacturers are not recommended for use…